Chemical - Information |
|
|
| Comparisons of typical Chemical Analysis |
| Elements |
Kutch Seabond |
S & B Greek |
Wyoming Federal |
Wyoming Black Hill |
| S102 |
45.43 |
60.83 |
58.14 |
66.12 |
| A1203 |
16.40 |
17.90 |
21.73 |
17.01 |
| FE203 |
14.05 |
4.34 |
2.46 |
2.46 |
| CAO |
1.18 |
1.90 |
0.86 |
1.37 |
| MGO |
2.43 |
2.83 |
2.42 |
1.51 |
| K20 |
0.13 |
1.98 |
0.52 |
0.54 |
| NA20 |
3.10 |
2.96 |
2.08 |
2.02 |
| TI02 |
1.86 |
N/A |
-- |
-- |
| 920 |
0.10 |
0.99 |
-- |
-- |
| L.O.I |
13.28 |
6.44 |
5.30 |
7.3 moisture% wt-- |
| Total |
97.96 |
100.17 |
93.51 |
98.33 |
|
|
| Foundry Chemical Analysis |
| Physical properties |
Unit |
Protocol |
Indounibond |
Indoexpobond |
Iindomaxbond |
Seabond |
| Base Exchange Capacity |
meq/100 gms |
IS 12446:1988 |
110 |
110 |
110 |
110 |
| Methylene blue value |
mg of MB/gm |
IS 12446:1988 |
400 + 20 |
420 + 20 |
420 + 20 |
420 + 20 |
| Swelling capacity |
cc |
IS 12446:1988 |
30 min |
35 min |
30 min |
35 min |
| Gelling time |
sec |
IS 12446:1988 |
Instantaneous |
Instantaneous |
Instantaneous |
Instantaneous |
| Gel formation index |
ml |
IS 6186:1986 |
80 - 90 |
85 - 95 |
80 - 90 |
85 - 95 |
| pH Value |
pH |
IS 6186:1986 |
9.0 - 10.0 |
9 - 10.2 |
9.0 - 10.2 |
9 - 10.5 |
| Liquid Limit |
ml/100 gms |
IS 12446:1988 |
800 min |
830 min |
830 min |
850 min |
| Green compressive |
psi |
IS 12446:1988 |
12 |
12.5 |
13 |
12 |
| Strength using 40/60 |
|
|
|
|
|
|
| sand in the ratio 10:4 (B:W) |
|
|
|
|
|
|
| Wet tensile strength (10:4 = B:W) |
N/cm2 |
IS 12446:1988 |
0.20 - 0.25 |
0.25 - 0.30 |
0.20 - 0.25 |
0.30 - 0.35 |
| Sieve analysis (WET) |
|
IS 6186:1986 |
|
|
|
|
| Passing 100 mesh |
% |
|
99 min |
99 min |
99 min |
99 min |
| Passing 200 mesh |
% |
|
90 min |
90 min |
90 min |
90 min |
|
|
O.C.M.A Specifications (Oil Companies Material Association)
O.C.M.A Parameters |
| PORPERTIES |
UNIT |
REQUIRED |
KM's INDOGEL RESULT |
YIELD:
YIELD OF A 15 CP.
APPARENT VISCOSITY,
BENTONITE/DISTILLED
WATER SUPPLY |
bbls/short ton (2000 lbs) |
90 min |
117.00 |
FLUID LOSS:
API FLUID LOSS OF A
SLURRY CONTAINING 7.5
GMS BENTONITE IN 100 MLS
DISTILLED WATER |
mls |
15 max |
14 mls |
| MOISTURE CONTENT: |
% by wt. |
13 max |
11.40% |
| SAND CONTENT |
% by wt. |
2.5 max |
1.60% |
DRY SCREEN ANALYSIS
(THRU US STANDARD SIEVE NO. 00) |
% by wt. |
98 min |
99.8% |
|
|
| KM's API Bentonite Specification |
| Description |
Polymer Extended KM Bentonite |
| Application |
Recommended for oil well drilling, slurry trenching, pond sealing and most other civil engineering applications. |
| Typical Yield |
KM DADA Gel will yield 91 barrels (minimum) of API fluid to one ton of material |
| Specifications |
| SPECS |
TYPICAL ANALYSIS |
API SPECS |
| Fann @ 600 rpm |
35 - 40 |
30.00 |
| Fann @ 300 rpm |
25 - 30 |
15 max |
| Plastic Viscosity |
10 |
13 max |
| Yield Point/Plastic |
1.5 - 2.0 |
3 Maximum |
| Viscosity Ration |
- |
- |
| Filtrate |
13.5 ml. |
15.0 Maximum |
| Dry Sieve Analysis |
78% - 80% (-200 Mesh) |
- |
| Wet Sieve Analysis |
2.5% - 3.0% |
4.0 Maximum |
| Moisture |
7.0% - 9.0% |
10.0% Maximum |
| pH (6.0% solution) |
8.5 - 9.5 |
|
NOTE: This product has been treated with a small amount (0.25%) of non toxic polyacrylate polymer to strengthen the viscosity of the bentonite. Please write or call if further information is needed on this.
Testing conforms to API specification 13A, Section 4.
The information contained herein is based on tests believed to be reliable, however no warranty is implied. |
|
|
|
| NONTREATED API Bentonite Specification |
| Description |
NONTREATED KM Bentonite |
| Application |
Recommended for oil well drilling, slurry trenching, pond sealing and most other civil engineering applications.. |
| Typical Yield |
KM DADA Gel will yield 91 barrels (minimum) of API fluid to one ton of material |
| Specifications |
| SPECS |
TYPICAL ANALYSIS |
API SPECS |
| Fann @ 600 rpm |
35 - 40 |
30.00 |
| Fann @ 300 rpm |
25 - 30 |
15 max |
| Plastic Viscosity |
10 |
13 max |
| Yield Point/Plastic |
1.5 - 2.0 |
3 Maximum |
| Viscosity Ration |
- |
- |
| Filtrate |
13.5 ml. |
12.5 Maximum |
| Dry Sieve Analysis |
78% - 80% (-200 Mesh) |
- |
| Wet Sieve Analysis |
2.5% - 3.0% |
4.0 Maximum |
| Moisture |
7.0% - 9.0% |
10.0% Maximum |
| pH (6.0% solution) |
8.5 - 9.5 |
|
| The information contained herein is based on tests believed to be reliable, however no warranty is implied. |
|
|
|
| Iron Ore Pelletizing (Taconite Pelletizing) |
| Moisture |
12% |
| PhValue |
8% - 10%. |
| Swelling |
30% -33% |
| Liquid Limit |
650% - 700% |
| Gel Index |
85% - 90% |
| Passing Through 200Mesh |
90% |
| Methylene Blue Test |
Upto 440% |
| Active Clay |
87% |
|
| |
